Ryobi Drill Drivers

Ryobi CHD1201 12v | Ryobi CHD1202 12v | Ryobi CCD-1441 14.4v | Ryobi CHD-1441 14.4v  | Ryobi CHD-1442 14.4v | Ryobi CCD-181M One+ 18v | Ryobi CHD-1801M One+ 18v | Ryobi CHP-1802 18v | Ryobi CHP-1802M One+ 18v  | Ryobi CHD1201 12v

Ryobi 12v Cordless Drill Drivers

Click to Compare Prices!!

   

Ryobi 14.4v Cordless Drill Drivers

     

Ryobi 18v Corldess Drill Drivers

       

Ace examples of 12v Cordless Drill Drivers include the Black & Decker CD12CA 12v, Bosch GSR12-2 12v, DeWalt DC772KLV 12v, Hitachi 12DVF3 12v, Makita 312DWDE3 12v, and the Ryobi CHD1201 12v

In the event that 14.4v Cordless Drill Drivers are more ideal, then be sure to take a peek at the Black & Decker Lithium Ion 14.4v, Bosch GSR Tough 14.4v, DeWalt DC731KA 14.4v, the Hitachi DSDL Li-Ion 14.4v,Makita BDF441RFE 14.4v, or the Ryobi CHD-1441 14.4v

For coverage of your 18v Cordless Drill Drivers needs, compare prices of the Black & Decker CD18CA 18v, Bosch PSR18VE-2 18v Drill Driver, DeWalt DC759KB 18v Drill Driver, Hitachi DS18DFL 18v Drill Driver, the Makita BDF452RFE 18v Drill Driver or the Ryobi CHP-1802M One+ 18v Drill Driver

Ryobi Drill Drivers - Some Safety Tips for DIY

In the world of cordless drill drivers, power is measured in battery voltage. Higher voltage means more torque-spinning strength to overcome resistance. Over the last decade, top-end voltage has increased from 9.6 to 18V, but the range of models include 6, 7.2, 9.6, 12, 14.4 and 18V. Today's higher-voltage drill drivers have enough power to bore big holes in framing lumber and flooring. That's impressive muscle. But the trade-off for power is weight. A typical 9.6V drill weighs 3 1/2 lbs, while an 18V model weighs up to 10 lbs.

Electric rotary drill drivers are made mainly for drilling metal and wood. This type of drill is normally small and compact. Motor sizes range from around 500 watts. The lower wattage motors are ok for drilling small holes or minimal use, the more powerful motored machines may cope with larger size holes and more frequent use. The chuck size is another thing to check, the smaller drill drivers have a chuck which may only accept drill bits up to 10mm diameter the larger chuck size is 13mm.

The least expensive drill drivers run at a single speed, but most have two fixed speeds: 300 rpm and 800 rpm. A slide switch or trigger lets you select high or low speed. These drill drivers are ideal for most light-duty operations. The low speed is for driving screws, the high speed for drilling holes. For more refined carpentry and repair tasks, chose a drill that has the same two-speed switch and a trigger with variable speed control that lets you vary the speed from 0 rpm to the top of each range. And should you do more hole drilling than screwdriving, look for more speed, 1000 rpm or higher at the top end.

Cordless drill drivers are measured in volts. Drills are available in everything from around 2 volts (for a cordless screwdriver) to the newest 24-volt tools. Higher voltage means heavier weight so think about buying a tool that may meet 80-90% of your needs. Twelve to 14.4 volt models are the most popular, and they may usually meet most homeowner's work needs. Corded drills are measured in amps. Generally, a higher amperage motor means more power.

Lithium ion batteries are commonly used in consumer electronics and tools such as drill drivers. They are currently one of the most popular types of battery for portable electronics, with one of the best energy-to-weight ratios, no memory effect, and a slow loss of charge when not in use. In addition to uses for consumer electronics, lithium-ion batteries are growing in popularity for defence, automotive, and aerospace applications due to their high energy density. However certain kinds of mistreatment may cause Li-ion batteries to explode.

Unlike Ni-Cd batteries, lithium-ion batteries may be charged early and often. However, should they are not used for a long time, they may be brought to a charge level of around 40% - 60%. Li-ion batteries may be kept cool. Ideally they are stored in a refrigerator. Aging may take its toll much faster at high temperatures. The high temperatures found in cars cause lithium-ion batteries to degrade rapidly. Storing a Li-ion battery at the correct temperature and charge makes all the difference in maintaining its storage capacity. It is significantly beneficial to avoid storing a lithium-ion battery at full charge. A Li-ion battery stored at 40% charge may last many times longer than one stored at 100% charge, particularly at higher temperatures.

When drilling deep or large holes, it is best to drill a small pilot hole first. This is very helpful when drilling deep holes because it's sometimes easier to keep the hole straight with a smaller bit. A larger bit may then normally follow the pilot hole. When drilling larger holes, especially in metal, the pilot hole opens an area in the metal to accommodate the tip of the larger bit so the cutting surfaces can more easily reach the uncut metal. Once you've drilled your hole, you'll probably find a burr on the back surface of your material. This can be removed by lightly drilling the back side of the hole with a larger bit. If the material is thin, such as sheet metal, instead of a burr you may find the material is actually distorted leaving a ragged hole. This be prevented by sandwiching the material between two pieces of wood before you drill the hole. As with all tools, exercise caution, wear safety equipment and learn to use the tools properly.

There may be occasions when you have to drill a hole at an angle. In these cases drill carefully. You can draw a pencil line on the material noting the angle and then try to follow that pencil guide as you drill. There are also angle guides you can use. Place these over the spot you want drilled with the guide calibrated at the correct angle. Insert the drill bit into the guide and drill away. If you are drilling completely through the material when the drill bit begins to exit out the other side of the material be careful, especially with wood. The drill bit exiting the wood can splinter the wood around the exit point. If it may show, you might want to sand it smooth. Better yet prevent the splintering by covering the exit point with masking or duct tape. The tape may decrease should not prevent the splintering.

Also known as a wood or dowel bit, a spur point bit has a central point and two raised spurs that help keep the bit drilling straight. The bit cuts timber very fast when used in a power drill and leaves a clean sided hole. They are ideal for drilling holes for dowels as the sides of the holes are clean and parallel. Sizes range from 3 to 10mm. Spur point bits may only be used for drilling wood or some plastics. Sharpen the point and spurs with a fine file or edge of a fine grindstone; the angle between the point and spurs may be 90°.

DIY Safety tips:

Use a voltage tester to check the power to the wires or connections are off before touching them. Check your work thoroughly before restoring power to the circuit. If you are not certain, seek professional help. Remember the golden rule ... " If you don’t know – ask".
Wear protective clothing including safety goggles, gloves and dust mask when working with potentially hazardous materials such as glass or spray paint. It is also advisable to wear a mask when working in a dusty environment e.g. sawing wood or MDF.

Don't wait until disaster strikes to find your stop-cocks and gate valves. Opening and closing them four times a year may ensure they easily work when you need them to. Don't let a blown fuse leave you in the dark: keep a repair kit nearby your mains fuse box, with a torch - check the batteries regularly - screwdrivers, spare fuses, bulbs and fuse wire, rubber gloves and insulated pliers, a trimming knife and insulating tape.

Do not work with electricity in damp or wet conditions. If you MUST, always use an RCD. Always place the cable of a hedge trimmer or mower over your shoulder and keep it behind you at all times.

Be sure you know the correct way to use all the tools. Many have very sharp blades.